The Hayward S-200 High-Speed Sand Filter is a fully corrosion-resistant and high-performance filter that combines superb flow properties and characteristics with ease of use. It is the latest in high-speed sand filtration technology.
The Hayward S-200 is practically reliable and dependable in terms of design and operation. If installed, used, and maintained following the manufacturer’s provided instructions, it will ensure clear, healthy, and sparkling water with minimal care and attention.
The process of replacing sand in Hayward pool filters may seem easy and sometimes daunting because it is a task to be done once every three years. A sand filtration system is exceptional in design because it can be more effective at capturing debris and common bacteria as the sand ages. It is recommended to replace your sand when you start feeling ineffectiveness after three years have come and gone.
The below listed step-by-step guides will help you:
- First, switch off the pump and shut any flap attached to the filter to avoid too much water loss and locate the drain lid at the tank bottom, open it and allow the water to dry off completely.
- Get rid of the sand filter flap gripped together with a C-lamp two screws and then gently turn off the valve to prevent the connected standpipe from cracking.
- After removing the filter valve, you’ll see the tank’s inner side and the sand that should be removed. Utilize your hand or industrial vacuum to evacuate the sand.
- Once you evacuate the majority of the sand, scrub the tank’s interior with water and remove the remaining debris. Now the laterals and standpipe are clean and exposed, and ready to take new sand. Check if the lateral is not cracked to avoid sending sand into your pool.
- Cover the top of the standpipe and reposition the previously removed lid and drain cap from the tank bottom. Fill the tank bottom with more till the laterals are engulfed.
- Start adding new filter sand and ensure the standpipe is centralized.
- Replace your sand filtration valve and re-attached all the pipes leading to and from the filter system.
- Ensure you backwash the filter before you start using it on the filter cycle.
Are you one of those who frequently relish clean and clear water produced by Hayward sand filter? Are you always happy with the filtration system, even with its encountering some challenges now and then? Hayward S-200 Sand Filter Troubleshooting will save you a lot of money and energy. Now that you are enjoying your pool and know how important it is to you, you may need to know why it is essential to learn how to take care of minor issues.
Troubleshooting minor problems without the need for expert intervention will enable you to enjoy your pool for an extended time uninterruptedly. Taking advantage of basic troubleshooting with the usual pool maintenance routine will give you a fantastic experience that will make you happy each time pool season rolls around.
If you have always been wondering or thinking seriously about the Hayward S-200 sand filter and how much sand you will need to put in it. Experts recommended that you need to adhere to the manufacturer’s instructions strictly. However, the Hayward S-200 sand filter needs 200 pounds of sand.
Another question that is likely to be bothering your mind is what kind of sand to use in pool filter? The answer is simply Silica sand, which is the most appropriate sand for filtering media. Every sand is not created the same, and if you want to change your existing media with sand, silica sand is the best. Silica sand number twenty will filter down to twenty microns and take care of all floated debris in the pool water.
Sand Pool Filter Instructions
Follow the below listed instructions to install your sand filter system:
- Gather and attach the pump to the clinging base
- Install laterals and centralized standpipe in the filtration basin
- Put the tank at the mounting base
- Enclose the opening inner hose to avoid sand entry and ensure the internal pipe is tightly secure in place
- Fill the tank with halfway water to suppress the filter sand
- Pour an appropriate quantity of sand into the tank with care and make sure the center pipe remain centralized
- Assemble filter control flap to the top of the filter basin
- Put the control flap to the filter tank neck
- Coat the Teflon tape on the thread of pressure gauge and place it inside the taped hole on the flap body
- Attach the pump to control flap and reconnect the pool pipe and ensure you make all other essential plumbing connections